您好，欢迎光临西宁从启成功保温材料厂|西宁保温材料|西宁防水材料|青海保温防水材料|西宁硅酸盐|青海硅酸盐 ！
　    橡塑保温材料在上世纪70年代末在国外一些发达国家就已经开始了用到了建筑节能方面，强制建筑业在新建建筑中执行节能标准使用橡塑保温材料，橡塑保温材料在发达国家的应用及对建筑节能的重视并采取的一些行之有效措施，这些国家取得了巨大的成效，建筑能耗大幅度下降。如丹麦使用了橡塑保温材料后， 1985年比1972年采暖面积增加了30%，但采暖能耗却减少了318万吨标准煤，由此可见，国外的建筑节能法规30多年来取得了显著的社会效益和经济效益。
　　橡塑绝热保温材料的安装应注意以下几点：
　　1、 所有的割隙、接头都需用东洋牌专用胶水粘接密封。
　　2、 安装后所有的三通、弯头、阀门、法兰和其他附件都需达到设计厚度。
　　3、 胶水粘结时不要太用力，所有材料间的接口应在轻微挤压下粘合。
　　4、 安装时应先大管后小管，先弯头、三通后直管，最后阀门、法兰。
　　5、 当安装冷冻水管和制冷设备时，橡塑管材的两端和铁管之间的空隙都需涂上胶水粘结起来，粘接宽度应不等于橡塑材料厚度。
　　6、 管道的割隙口应尽量安装在不显眼处，且两条管材的割隙口应相互错开。
　　7、 机器在使用中不要安装。装好后36小时内切勿开机。
　　8、 大管径橡塑管由于包装关系已变成椭圆形，剖开时请剖较扁平的那边。

    Rubber and plastic heat preservation material in the late 1970 s in some developed countries abroad have begun to building energy efficiency, mandatory construction in the new building energy saving standards using rubber insulation materials, rubber and plastic heat preservation material in the application of the developed countries and emphasis on building energy efficiency and take some effective measures, the country has achieved great success, building energy consumption dropped substantially. After using the rubber insulation materials such as Denmark, heating area increased by 30% in 1985 than in 1972, but heating energy consumption is decreased by 3.18 million tons of standard coal, therefore, building energy conservation regulations abroad for more than 30 years made significant social and economic benefits.西宁保温材料|西宁防水材料|青海保温防水材料|西宁硅酸盐|青海硅酸盐
     Rubber insulation material the installation should pay attention to the following:
    1, all the cutting gap, joint with Oriental brand special glue adhesive sealing.
    2, after installation of all the three links, elbow, valve, flange and other accessories are required to meet the design thickness.西宁保温材料|西宁防水材料|青海保温防水材料|西宁硅酸盐|青海硅酸盐
Don't too hard, 3, glue bonding interface between all the materials should be under mild extruding glue.
    4, when installation should first fill small tube, after the first straight tube after elbow, tee, valves, flange in the end.
     5, when installing a chilled water and cooling equipment, rubber and plastic will be the gap between the ends of the pipe and pipe coated with adhesive glue, glue the width should be no is equal to the thickness of rubber and plastic materials.西宁保温材料|西宁防水材料|青海保温防水材料|西宁硅酸盐|青海硅酸盐
     6, cutting the pipe mouth gap, should be installed in an inconspicuous area and two pipe cutting gap should be staggered.西宁保温材料|西宁防水材料|青海保温防水材料|西宁硅酸盐|青海硅酸盐
Do not install
    7, the machine is in use. Do not boot loaded after 36 hours.
   8, big diameter rubber tube due to relationship has become oval packing, please split the flat side when they cut it open.
您好，欢迎光临西宁从启成功保温材料厂|西宁保温材料|西宁防水材料|青海保温防水材料|西宁硅酸盐|青海硅酸盐 ！

http://xn.114chn.com/mallhtml/630100/6301001105170095/index.html